Plumbing is a licensed trade with a verifiable paper trail and an unverifiable reputation, and a resume has to deal with both.
The license, the class, and the hours can be checked against the state board in minutes. What cannot be checked is the thing that actually decides whether a contractor hires you: your callback rate, and what you do about a leak you caused.
The ten examples below cover the range plumbing contractors hire across — apprentice through master, residential service, new construction, commercial, gas, backflow, drain and sewer, and a career changer. Each is built around a number a service manager would recognize.
Plumber Resume Examples by Level and Specialty
Pick the one closest to your position — a stage in the apprentice-to-master progression, or a specialty. The figures are illustrative; swap in your own and keep the shape.
Apprentice Plumber
Best for: registered apprentices and helpers moving into a formal program.
Hours are the position and this example states them first. Field work is described by system and scale — DWV rough-in, water distribution, fixture sets — rather than by who supervised it.
- Hours logged out of hours required, in the header.
- Classroom units named with results.
- Work described by system, not by supervisor.
Residential Service Plumber
Best for: service plumbers on residential accounts, including drain work and water heater replacement.
Service is a volume job and this example gives the volume: calls per day, first-visit resolution, average ticket and customer rating. It also names callbacks on its own work, which is the figure most service resumes avoid.
New Construction Plumber
Best for: production residential and multifamily rough-in and trim work.
Production plumbing is measured in units and days per unit. This example gives both, alongside the rough-in inspection record, which is the quality figure a builder tracks.
- Units completed and days per unit.
- Rough-in inspection pass rate.
- Material waste against budget.
Commercial Plumber
Best for: commercial and institutional work under a general contractor.
Projects are the currency and each one here carries a size: square footage, fixture count, pipe sizes and materials. Medical gas certification gets its own line because it changes which jobs you can be sent to.
Journeyman Plumber
Best for: licensed journeymen running their own work and leading an apprentice.
The license line sits in the header. Below it the example does what most journeyman resumes will not: gives the callback count against the job count, and describes one leak it caused and repaired.
- License, state, number and standing up top.
- Callbacks owned with the repair.
- Inspection record stated as a ratio.
Master Plumber
Best for: master plumbers pulling permits, qualifying a contractor or moving into estimating.
At master level the resume shifts from work performed to work authorized. Permits pulled, plan-review corrections, contract values, and the code questions that stopped at the writer rather than going to the inspector.
Gas Fitter
Best for: plumbers holding a separate gas license or endorsement.
Gas work is a separate authorization and this example treats it that way: the license class, appliances commissioned, pressure test records, and combustion analysis. It is the clearest example on the page of a credential that changes what you can be dispatched to.
Backflow & Cross-Connection
Best for: certified backflow testers and cross-connection control specialists.
A recurring, certifiable, documented specialty. This example gives annual test volume, repair rate, and the municipal reporting relationship — which is the part employers care about and applicants omit.
Drain & Sewer Technician
Best for: drain cleaning, camera inspection and trenchless repair work.
This example leads with equipment and diagnostic volume: camera inspections run, hydro jetting, and lining or pipe-bursting jobs completed. Equipment names do real work on a drain resume.
Career Changer
Best for: people entering plumbing from another trade or another career.
This example does not oversell the transfer. Pre-apprenticeship completed, hours logged, the specific overlap from the prior job, and an application at the level the hours actually support.
Anatomy of a Plumber Resume
Four parts carry the document. Replace the bracketed sections with your own.
The header, with the license
Class, state, number, standing. It is the first screening question and it should not require scrolling.
DANIEL R. [SURNAME]
Journeyman Plumber — [State], Lic. #[PJ-00000], active through [Month Year]
Gas Fitter endorsement [Class B] · Backflow Tester cert. #[00000]
[City, State] · ([000]) 555-0000 · [name]@email.com
OSHA 10 · Confined Space · Own truck and tools · [40]-mile service radius
The summary, carrying a number
Three lines and at least one checkable figure. A summary without one is the part that gets skipped.
Licensed journeyman with [eight] years in residential service and light commercial, running [8–10] calls a day and resolving [87%] on the first visit. [Two] callbacks on my own work in [18] months, both repaired at no charge within [24] hours. Comfortable on [copper, PEX and cast iron], water heater and tankless replacement, and gas appliance connection under a [Class B] endorsement.
The bullet formula
Action, system, scale, outcome. Scale is what separates a bullet from a job description.
• Replaced [142] water heaters in twelve months including [31] tankless conversions, each permitted and passed on final inspection
• Rough-in and trim on [38] multifamily units at an average of [1.4] days per unit against a [1.7]-day budget
• Repiped [19] homes from galvanised to [PEX], with [zero] callbacks and an average [2.5]-day completion
• Diagnosed a recurring slab leak on a [1970s] copper system using [acoustic and thermal] location, avoiding roughly [$6,000] of exploratory demolition
The skills block
Name the materials, the methods, and the equipment. Generic phrasing reads as inexperience.
Materials and methods: copper (soldered and press), PEX ([brand] expansion and crimp), [CPVC], cast iron, [ProPress], [no-hub couplings]
Systems: DWV, water distribution, water heaters and tankless, [recirculation], backflow assemblies, gas piping to [2 in]
Equipment: [RIDGID] camera and locator, [sectional and drum machines], hydro jetter to [4,000 psi], combustion analyzer, press tool
Code: [IPC/UPC] with [state] amendments, permit and inspection process
Copy-Ready Summaries and Bullets by Specialty
Four blocks you can adapt directly, each written for a specific lane rather than a generic plumber.
Apprentice summary
Hours first; everything else is read in that context.
[Third]-year apprentice, [4,100] of [8,000] hours, [UA Local 130], currently in year-three classroom covering [venting, sizing and gas]. Field time has been about [60%] residential new construction and [40%] service. Have rough-in and trimmed roughly [70] units and assisted on [about 400] service calls. No lost-time incidents across approximately [2,900] hours.
Service bullets
Volume, first-visit resolution, callbacks, and the ticket. Service managers read all four.
• Carried an [8–10] call day across residential service, resolving [87%] on the first visit
• Generated [$412K] in service revenue last year at an average ticket of [$486]
• Recorded [two] callbacks on my own work in [18] months, both repaired at no charge within [24] hours
• Held a [4.9]-star average across [340] reviewed calls with [zero] formal complaints
Commercial bullets
Give every project a size, and name the materials and pipe sizes.
• Installed underground and above-ground DWV for a [64,000 sq ft] medical office, including [6 in] cast iron mains and [142] fixture connections
• Completed [medical gas] rough-in and certification coordination on [three] surgical suites under [NFPA 99]
• Ran [2 in] natural gas distribution to [11] rooftop units with pressure testing documented at [1.5x] working pressure
• Delivered a [$1.4M] plumbing package on an [18]-week schedule with [two] RFIs and no schedule impact
Master summary
Authorization rather than labor. Permits, corrections, and the code questions that stopped with you.
Master plumber qualifying a [commercial] contractor and pulling permits on projects to [$2.6M] plumbing value. Pulled [78] permits over [four] years with [three] plan-review corrections and no revocations. Act as the internal code authority on roughly [35] questions a year, cutting inspector pre-submission meetings from [7] a year to [2]. Sealed [fixture unit and pipe sizing] calculations on [26] projects.
Skills and Keywords Contractors Search For
- Everyone: the license class and number, the code you work to (IPC or UPC) with state amendments, permits and inspections, OSHA 10 or 30.
- Service: call volume, first-visit resolution, water heater and tankless replacement, drain clearing, leak location, customer-facing work.
- New construction: DWV rough-in, water distribution, units per week, PEX systems by brand, slab and underground work.
- Commercial: cast iron and no-hub, pipe sizes, grease interceptors, medical gas (NFPA 99), backflow assemblies, RFIs and as-builts.
- Gas: license class or endorsement, appliance commissioning, pressure testing, combustion analysis, CSST and black iron.
- Drain and sewer: camera inspection and locating, hydro jetting pressures, trenchless lining and pipe bursting, municipal tie-ins.
Naming the equipment matters: “RIDGID SeeSnake and a 4,000 psi jetter” tells a service manager exactly what you can run, where “drain cleaning equipment” does not.
What Counts as Proof
Licensed journeyman, State of Texas, active. 8-10 calls a day with 87% first-visit resolution; two callbacks on my own work in 18 months, both repaired at no charge within 24 hours. 142 water heaters replaced last year, 31 of them tankless conversions.
Dedicated plumber with extensive experience in residential and commercial plumbing, committed to quality workmanship and excellent customer service on every job.
The second could be written by somebody who has never held a license. The first could not.
The Callback Paragraph Most Plumbers Leave Out
Every plumber with real hours has caused a leak. Writing about one is the single most credible thing you can do on this document, and almost nobody does it.
The useful version has three parts: what happened, what it cost, and what you changed. “A press fitting on a 1 in copper main had a bad crimp that showed up overnight; about $2,800 of drywall and flooring, repaired at the company’s cost, and I now pressure-test every press joint on a main before leaving” reads as somebody who has been doing this long enough to be honest about it.
A service manager has seen hundreds of resumes claiming zero callbacks. They have also seen the actual callback data for their own crews, which is never zero. Giving a real number with the repair attached is more persuasive than a perfect record nobody believes.
The Same Experience, Written for Three Employers
- Residential service companies: lead with call volume, first-visit resolution, average ticket and customer rating. They are hiring somebody who will be alone in a customer’s house and whose work generates reviews.
- New construction and multifamily: lead with units, days per unit, and inspection pass rate. They are buying production against a schedule and a budget.
- Commercial contractors: lead with projects and sizes, materials, and the specialty certifications. They are buying somebody who can read a print and work alongside other trades.
One document covers all three if the summary is rewritten and the bullets reordered per application. Changing the top three lines does more than rewriting the whole resume.
Permits and Inspections Are a Skill, Not Paperwork
Plumbing is inspected more often than most trades and the inspection record is the closest thing the field has to a quality score. It belongs on the resume as a ratio.
“Rough-in and final passed on first inspection on 29 of 32 permitted jobs; the three corrections were a missing cleanout, an unsupported horizontal run, and a vent termination distance” is a complete account. It shows the record, shows you know why each failed, and shows you have not confused a correction with a disaster.
If you pull your own permits, say how many and over what period. A journeyman who has pulled permits has dealt with plan review, scheduling, and an inspector’s preferences — all of which a contractor would otherwise have to teach.
On-Call and Emergency Work Deserves Its Own Line
A large share of a service plumber’s value is availability, and it almost never appears on the resume in a usable form. A contractor staffing a rotation wants to know whether you have actually carried a pager and what happened when you did.
Give it as a line: how often you were on call, the response-time standard you worked to, and the volume. “On call one week in four with a two-hour response standard, averaging 11 after-hours calls per rotation” is specific and hireable. “Available for emergency calls” is not.
The same applies to weather events and burst-pipe season. Plumbers who have worked a hard freeze know things about triage and parts availability that cannot be taught quickly, and a single line naming one makes that visible. For the general structure of a trades application, the resume format guide covers when reverse-chronological is and is not the right choice.
Mistakes That Cost Plumbers Interviews
Check your draft against these
- License buried below the work history. It is checked first; put it in the header.
- No hours for an apprentice. The hours are your position in the trade.
- Zero callbacks claimed. Nobody believes it. Give a real number with the repair.
- Projects with no size. Square footage, unit count, or fixture count — pick one and use it every time.
- Gas and backflow folded into a list. They are separate authorisations; give each its own line.
- “Drain cleaning equipment.” Name the machines and the jetter pressure.
- No code named. IPC or UPC with your state’s amendments, stated once.
- Unexplained gaps. Seasonal and layoff gaps are normal; one line settles each.
Format, Length and the Practical Questions
One page to about ten years; two for a master or a service manager with a long list. Reverse-chronological with the license header on top. A plain layout is the safe choice — our ATS-friendly resume templates work for larger service companies running applicant tracking, and a professional template suits a direct application to a small shop.
Answer the practical questions: own truck and tools, service radius, on-call availability, and whether you can start on a date. For service work these decide hiring as often as the wording does.
Applying outside the US changes the document — see the plumber CV examples for how qualification recognition and gas registration are handled. Pair the application with the plumber cover letter examples, and browse the skilled trades resume examples for the neighbouring trades.
Ready to write your Plumber resume?
Turn what you just read into a resume that gets you shortlisted for Plumber roles.
Create ResumePlumber Resume FAQ
Where should the license go?
In the header under your name, with class, state, number and expiry. Gas and backflow endorsements belong on the same block, because they change which work you can be dispatched to.
Should I really list callbacks?
Yes, with the repair attached. A service manager knows their own crews’ callback data and reads “zero callbacks” as either inexperience or a claim nobody is counting. A real number with what you did about it reads as a professional.
How do I write a resume with mostly helper experience?
Describe the work by system and scale rather than by who you assisted. “Rough-in and trim on about 70 multifamily units” is concrete; “assisted journeymen with plumbing installations” is not.
Do I need to list every project?
No. List the ones with scale or a transferable system and summarize the rest in one line. Eight projects with fixture counts beat twenty-five names.
How much does the gas endorsement matter?
A great deal for service work, because it decides whether you can be sent to a water heater or furnace call alone. Give it its own line with the class, not a mention inside a skills list.
Is medical gas certification worth putting high up?
On commercial applications, yes. ASSE 6010 or 6040 narrows the field considerably on healthcare projects and is worth a line of its own near the top.
One page or two?
One for apprentices and journeymen. Two for a master or service manager, and only if the second page is projects or permits with figures.
Related roles in this field, written the same way: Welder, Automotive Technician and HVAC Technician.
Need a CV instead of a resume for this role? See our CV example for Plumber.









